Results 1 to 14 of 14

Thread: Breaking A-Strings in CGDA tuning

  1. #1

    Default Breaking A-Strings in CGDA tuning

    All ... I change between standard CGDA tuning and DADF# and CGCG open tunings regularly. Unfortunately the A-string will only take about a half-dozen changes before it snaps. I changed to EFS reentrant tuning using all wound strings in hopes that it would last longer; it does but not much longer. Yesterday I broke the A-string at a most inopportune time and had to suffer the embarrassment of finishing with 3 strings. Does anyone have any suggestions as to what I might use as a more durable A-string? As always, thanks in advance.

  2. #2
    Registered User fox's Avatar
    Join Date
    Feb 2014
    Location
    Guernsey... small island just off the coast of France
    Posts
    1,469

    Default Re: Breaking A-Strings in CGDA tuning

    You could use a 21” scale as a steel A string will always be near it limit on a 23” scale.

  3. #3
    Harley Marty
    Join Date
    Mar 2016
    Location
    Mullingar Co Westmeath Ireland
    Posts
    116

    Default Re: Breaking A-Strings in CGDA tuning

    I find that plains take the tension better than wounds. I broke a new nickel wound putting it on yesterday & the string was below G# & I was going up slow slow slowly, thatís annoying too

  4. #4

    Default Re: Breaking A-Strings in CGDA tuning

    If it's snapping at the tuning machine there's a very good chance there are sharp edges or burrs cutting into the string. This often happens after the stem is drilled out for the string. This is easily fixed with a bit of sandpaper. Remove the string and sand the tuning machine's stem where the string enters and exits the hole until smooth.

    If the string is of a light gauge with a lot of tension I find it often helps to tune to pitch in batches. If you try doing it all at once the friction causes the string to vibrate and heat-up making it more susceptible to breakage. Go slow and tune up - let it cool - tune more - let cool - and etc.
    VerneAndru.com | oKee.ComX

    - ---==< V >==--- -

  5. #5
    Lord of All Badgers Lord of the Badgers's Avatar
    Join Date
    Jan 2013
    Location
    South West UK
    Posts
    1,104

    Default Re: Breaking A-Strings in CGDA tuning

    I put really heavy sets on my GDAE tuned tenor... It's normal lol. I hate light strings
    My name is Rob, and I am Lord of All Badgers

    Paul Shippey custom "Tone" Octave Mandolin, Paul Shippey "Axe" Bouzouki,
    Phil Davidson A5 "Badgerlin" mandolin, Phil Davidson F5 mandolin,
    Mcilroy Tenor Guitar, Phil Davidson Tenor Mandola
    My band's website

  6. #6
    Unfamous String Buster Beanzy's Avatar
    Join Date
    Sep 2009
    Location
    Cornwall & London
    Posts
    2,602
    Blog Entries
    4

    Default Re: Breaking A-Strings in CGDA tuning

    I get this if I go too heavy on my mandoloncello. I put most of a set of the D’Adario MC strings on but use a lighter A, which seemed a bit backwards, but it was because the heavier strings needed more tension and my longer scale was too much for them. On the basis of my experience on the big beasty, Id say maybe try a lighter A on your tenor guitar to see if they survive longer by being under less strain when tuned.
    Eoin



    "Forget that anyone is listening to you and always listen to yourself" - Fryderyk Chopin

  7. #7
    Lord of All Badgers Lord of the Badgers's Avatar
    Join Date
    Jan 2013
    Location
    South West UK
    Posts
    1,104

    Default Re: Breaking A-Strings in CGDA tuning

    Didn't finish last post!
    My tenor is
    .49
    .32
    .26
    .16
    23"
    I sense I may have over done it...
    My name is Rob, and I am Lord of All Badgers

    Paul Shippey custom "Tone" Octave Mandolin, Paul Shippey "Axe" Bouzouki,
    Phil Davidson A5 "Badgerlin" mandolin, Phil Davidson F5 mandolin,
    Mcilroy Tenor Guitar, Phil Davidson Tenor Mandola
    My band's website

  8. #8
    Registered User fox's Avatar
    Join Date
    Feb 2014
    Location
    Guernsey... small island just off the coast of France
    Posts
    1,469

    Default Re: Breaking A-Strings in CGDA tuning

    The A string on a 23” scale tenor guitar (cgda) is close to breaking, I have never tested it but I have read on this forum that they will break at 24”.
    I don’t think it matters what size the string is .. 09-010- 011 the string will still be at near breaking point when tuned to pitch.
    The difference will be the tension to reach breaking point but regardless of string diameter it will still be near breaking point.

    Badger, for me those string would be awful and very miss matched but if that is something you are used to then I guess they are the right strings for you!
    Your chosen gauges for a 23” tuned GDAE would be G 24lb D 24lb A 37lb E 34lb.

  9. #9

    Default Re: Breaking A-Strings in CGDA tuning

    Quote Originally Posted by fox View Post
    The A string on a 23Ē scale tenor guitar (cgda) is close to breaking, I have never tested it but I have read on this forum that they will break at 24Ē.

    I donít think it matters what size the string is .. 09-010- 011 the string will still be at near breaking point when tuned to pitch.
    The difference will be the tension to reach breaking point but regardless of string diameter it will still be near breaking point.
    This is correct. A plain steel wire will snap relatively quickly when tuned to G#4 at a scale length of 25.5"ring, and A#4 at a length around 24". The thinner the string, the easier it is to get to pitch, but the thinner string is too weak to last. The thicker the string, the stronger it is, but it requires so much tension to get to pitch that the string snaps.

    There *are* special alloy strings available which will get to higher pitches, but they won't withstand constant retuning and will snap.

    Going to an instrument with a 20" scale length or shorter is the only solution which will allow retuning to a high A4 and then lower, repeatedly, as desired by the OP without string breakage.

  10. #10
    Lord of All Badgers Lord of the Badgers's Avatar
    Join Date
    Jan 2013
    Location
    South West UK
    Posts
    1,104

    Default Re: Breaking A-Strings in CGDA tuning

    Quote Originally Posted by fox View Post
    The A string on a 23” scale tenor guitar (cgda) is close to breaking, I have never tested it but I have read on this forum that they will break at 24”.
    I don’t think it matters what size the string is .. 09-010- 011 the string will still be at near breaking point when tuned to pitch.
    The difference will be the tension to reach breaking point but regardless of string diameter it will still be near breaking point.

    Badger, for me those string would be awful and very miss matched but if that is something you are used to then I guess they are the right strings for you!
    Your chosen gauges for a 23” tuned GDAE would be G 24lb D 24lb A 37lb E 34lb.
    Science isn't my forte lol. I had a set on and the G was too floppy...
    My name is Rob, and I am Lord of All Badgers

    Paul Shippey custom "Tone" Octave Mandolin, Paul Shippey "Axe" Bouzouki,
    Phil Davidson A5 "Badgerlin" mandolin, Phil Davidson F5 mandolin,
    Mcilroy Tenor Guitar, Phil Davidson Tenor Mandola
    My band's website

  11. #11
    Registered User fox's Avatar
    Join Date
    Feb 2014
    Location
    Guernsey... small island just off the coast of France
    Posts
    1,469

    Default Re: Breaking A-Strings in CGDA tuning

    Ha ha well what ever works for you, just be aware that 120 lb of total string tension would very likely damage most tenor guitars.
    Perhaps you should use an octave mandolin with 4 strings!

  12. #12
    but that's just me Bertram Henze's Avatar
    Join Date
    Jun 2005
    Location
    0.8 mpc from NGC224, upstairs
    Posts
    9,804

    Default Re: Breaking A-Strings in CGDA tuning

    This rings a bell - a long time ago, I played a 19-fret tenor banjo in CGDA, and the A string was near breaking when tuned to pitch the first time - if it survived this and stayed tuned, it lasted quite a long time, but lowering and tuning up again was out of the question (down a half step and up again BANG). String change was like defusing a bomb every time. In the end, I sawed the nut slots down into the wood to make the first fret a zero fret and have an 18-fret banjo henceforth.

    There is a reason. Near the breaking point tension, steel goes from elastic to plastic deformation, i.e. microscopic fractures are beginning to develop. You have the same process when bending a spoon forwards, backwards, forwards, backwards until it breaks.

    Therefore, to make tuning changes possible, you must stay away from that tension limit by using lighter strings.
    the world is better off without bad ideas, good ideas are better off without the world

  13. #13
    Lord of All Badgers Lord of the Badgers's Avatar
    Join Date
    Jan 2013
    Location
    South West UK
    Posts
    1,104

    Default Re: Breaking A-Strings in CGDA tuning

    Quote Originally Posted by fox View Post
    Ha ha well what ever works for you, just be aware that 120 lb of total string tension would very likely damage most tenor guitars.
    Perhaps you should use an octave mandolin with 4 strings!
    Hm. It's a Mcilroy and pretty sturdy. He shipped it with a very heavy CGDA set.
    Bottom line is I have LITERALLY no idea how to use string tension calculators. It just doesn't work with my brain and no one has ever been able to get me to understand them

    How would this work?

    Oh incidentally been meaning to say to you - I bumped into that old archtop of yours at Wimborne folk festival a few weekends ago
    My name is Rob, and I am Lord of All Badgers

    Paul Shippey custom "Tone" Octave Mandolin, Paul Shippey "Axe" Bouzouki,
    Phil Davidson A5 "Badgerlin" mandolin, Phil Davidson F5 mandolin,
    Mcilroy Tenor Guitar, Phil Davidson Tenor Mandola
    My band's website

  14. #14
    Registered User fox's Avatar
    Join Date
    Feb 2014
    Location
    Guernsey... small island just off the coast of France
    Posts
    1,469

    Default Re: Breaking A-Strings in CGDA tuning

    Cool, I have sold 7 tenor guitars this year and I am building one to order right now but that is likely the last one as I Intend to sell my workshop.

    I am not familiar with your guitar so I can’t comment but most tenon guitars are far more happy with around 80- 90 lb total tension.
    However Blueridge tenor guitars are said to be fine with 100lb and I know there is one Blueridge (on this forum) that has been converted to 8 strings and has 140lb ! Although whether that one still works I can’t say?

    Personally I recommend 13 20 30 45 but I supply my 23” tenors with 12 18 30 45. to suit their light build.
    Perhaps a quick check with your guitar builder would be worth while.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •