Page 2 of 2 FirstFirst 12
Results 26 to 29 of 29

Thread: New Builders Tap tuning

  1. #26

    Default Re: New Builders Tap tuning

    Quote Originally Posted by Jim Hilburn View Post
    I would never say it's hogwash just because I don't understand it even though I've heard some of the big names say just that.
    My point is if you are on your first or so mandolin there are a lot of fundamentals to learn without getting off in the weeds too far.
    Ah yes, but having to take the back off is traumatic...I did this on my first scratch build, shaveed the bars and it improved greatly..

  2. #27

    Default Re: New Builders Tap tuning

    Quote Originally Posted by peter.coombe View Post
    Here we go again!

    First of all, you cannot tune individual parts. The whole thing vibrates as a whole. If you are tapping one tonebar you are exciting one mode of vibration, and another mode of vibration when you tap the other tone bar. You can see this clearly if you try Chladni patterns. This applies to free plates, partially assembled, or a finished mandolin with the strings on. Siminoff was correct in that it is useful to get the main modes of vibration of the finished mandolin with strings on between notes (from lots of research done on guitars), but the modes are whole body modes, not just individual parts so he got that bit wrong. Problem is, nobody has shown any relationship between modes of vibration of free plates or a partially assembled instrument to modes of vibration of the completed instrument. Note that the tailpiece and bridge will change the frequencies, so it gets complicated, and relationships are very likely to be non linear. There must be some sort of relationship because if you carve a top or back thicker then the frequencies must be higher in a free plate and also in the assembled instrument. The best we can do is to build a database of measurements and note down the sound, and form empirical conclusions without really knowing what the relationships are - i.e. if I do this then I get a certain sound. I did this with oval hole mandolins and published it -

    Problem with archtop instruments is that it is difficult to measure modes of vibration on the completed instrument. The best way is with laser interferometry which is very sensitive to frequency, but does not measure amplitude. Unfortunately you do need a laser interferometer which are not cheap so the average Luthier won't have one. Dave Cohen has published papers on this, but the average Joe will find these papers fairly heavy going, but they do indicate reality and not some hair brained theory. Suffice to say, mandolins are similar to guitars, but the frequencies are higher, and the frequencies vary depending on what type of mandolin it is.

    At the moment I am measuring free plates and completed instrument measurements on my pancake flattop mandolins to try and understand how this stuff works once the mandolin is assembled - i.e. can I predict what will happen from the free plate measurements. I am using my pancake mandolins because they are about as simple as a mandolin can be, yet still be a decent sounding mandolin, and are much easier to measure than arch top mandolins. This is likely to take years before I can make any sense out of it.
    Thanks Peter, gonna take a while to absorb these articles....

  3. #28
    Mandolin & Mandola maker
    Join Date
    Sep 2002
    Bega NSW, Australia

    Default Re: New Builders Tap tuning

    Just a couple of corrections (thanks Dave). Apparently laser interferometry does measure amplitude. Having never used the technique I was not aware it measured amplitude as well as frequency. That makes it quite a powerful technique, but unfortunately not accessible to most of us.

    Also I did not quite describe the technique of tapping and exciting the modes of vibration quite correctly. What modes and how much they are excited depends on where you tap and where you hold the object. In principle, all the modes are excited when you tap, but if you hold the object on an antinode then that mode it is not excited much at all. If you hold it on a node then it will be excited. Thus tapping one tone bar and tapping the other does not really excite two different modes exclusively unless you hold it on the node and antinode respectively. Sometimes that is possible if the node of one frequency corresponds with the antinode of the other (and you can see that from Chladni patterns), but often there is just a difference in amplitude which is what you hear. So, if you must tap tune you need to know where to tap and where to hold. Chladni patterns form on the nodes so can be useful in determining where to hold and where to tap.
    Peter Coombe - mandolins, mandolas and guitars

  4. #29

  5. The Following 4 Users Say Thank You to grandcanyonminstrel For This Useful Post:

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts