Results 1 to 4 of 4

Thread: Semi hollow design question

  1. #1

    Default

    I'm currently working on plans for building my second electric mando, and I have run into question I cannot answer. I plan to build a flat-top semi hollow with a koa soundboard, back, and sides. I'm using a neck through design with a maple neck. The center block will run the length of the body My question is that with the soundboard and back mounted on the center block, is any sort of bracing necessary? Will adding bracing help tone or sustain at all? Do other semi-hollow emando's use bracing? Thanks all.

  2. #2
    coprolite mandroid's Avatar
    Join Date
    Oct 2002
    Location
    Outer Spiral Arm, of Galaxy, NW Oregon.
    Posts
    15,203

    Default

    I think the load of the bridge is passing directly to the block under the top if its glued to it.

    routing out the wings on a otherwise solid body instrument with a nice piece of figured wood on the top would be a looker.

    I had a 4 string made.. Alder body's face was arched, after, cavities were cut out from the back,[a drill press used],
    leaving a solid strip down the middle, then the back was added.
    I provided a piece of Baltic all birch plywood for the back,
    and that is the whole back ,
    {its an A pear-shaped body}, rather than small panels behind the pots and such.

    a figured veneer on the back seemed superfluous , but that could be added, of course..



    writing about music
    is like dancing,
    about architecture

  3. #3
    Recipient of medication Cliff D's Avatar
    Join Date
    Mar 2008
    Location
    London, UK
    Posts
    191

    Default

    May I suggest you take a look at some semi hollow guitars & see what has been done there. As far as I'm aware my Epiphone has no internal bracing & the thru neck runs to the far belt stud, but I've not ripped it apart to see! As Mandroid points out, if the top is glued in place & the strings are anchored at the tail end to the same piece of wood that is the neck there seems little structural reason for bracing.

    I think bracing tends to inhibit table vibration & there is always a compromise between physical strength & acoustic properties in fully hollow instruments, but I don't have any real expertise to share in this department (although I know there are cafe members who do!).
    Sorry madam, but we are fresh out of bull-dogs today!

  4. #4

    Default

    A few factors will fall into play,how thick will the top be,
    and what type of bridge do you plan on using?

    I build semi-hollow mandolins and I have also built a couple
    of semi-hollow electric guitars. I have never found a need to
    add additional top braces. It won't hurt if you do want to add bracing.

    I agree that a neck thru design adds the support needed for the bridge. You could always glue a couple of blocks to the side of your neck shaft to widen the area at the bridge.

    I hope this helps. Feel free to ask if you have more ???s

    Tom

Similar Threads

  1. Glued up rim for semi hollow body
    By thistle3585 in forum Builders and Repair
    Replies: 13
    Last Post: Mar-02-2007, 4:32pm
  2. Semi-finished bridges
    By Darryl Wolfe in forum Builders and Repair
    Replies: 4
    Last Post: Jul-13-2006, 8:22am
  3. semi-hollow mando?
    By John Bertotti in forum Builders and Repair
    Replies: 2
    Last Post: Apr-28-2006, 3:05pm
  4. A Design Question
    By Antlurz in forum Builders and Repair
    Replies: 10
    Last Post: Aug-21-2005, 10:27am
  5. RISA SEMI HOLLOW BODY ELECTRIC MANDOLA
    By jongolin in forum Four, Five and Eight-String Electrics
    Replies: 3
    Last Post: May-15-2004, 4:53am

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •