Thanks Mark, I was just thinking about that. I didn't notice if mine had one or not before I removed the board. Is that a picture of your Alrite? The wood looks like it is mahogany and matches the neck.
Thanks for the pics Mark. The new fingerboard arrived in the morning and by the end of the day I had the dots in, frets trimmed and neck glued down. Also, there is a 1/4" carbon fiber rod embedded in the neck.
I found a piece of ebony for the wedge and doubled face taped it to a block, then shaped it with a belt sander.
After a back has been removed, it is difficult to get a good fit when reattaching the back. Mine was no exception. I had planned all along to use an edgebinding. I used some light colored cherry to match the back as best I could. These two pictures show the ledge for the binding and the binding installed. Next is a whole lot of sanding to prep for the finish.
This is way too late to help Tukanu, but it may help others.
A good way to remove a fingerboard [or a guitar bridge] is with a 1" x 5" 25 watt heat blanket, available from MSC Industrial or McMaster-Carr. A Harbor Freight router speed controller makes a good temperature control. Heat blankets allow you to put the heat right where you want it without posing risks to adjoining surfaces.
A 2" x 5" 50 watt heat blanket is useful for lifting guitar fingerboards. Heat blankets come in a variety of sizes and shapes. To calculate the power rating needed for any given size, use 5 watts per square inch.
Heat blankets and temperature controllers are also available from LMI, but the prices are considerably inflated.
Thanks to Lynn Dudenbostel for bringing this highly useful tool to my attention.
I am impressed by the speed at which Tukanu works. He must be younger than me . . .
Tukanu, you might want to consider French polished shellac, perhaps in conjunction with violin maker's oil varnish. Then you can work inside . . .
If you're interested in that, I doubt you'll have much trouble learning new finishing techniques.
The instrument would originally have been finished with varnish and/or shellac anyway.
Thank you for the information. The original fingerboard was made of pearwood. It basically crumbled when I tried to remove it. Thank you for the link to the heat blanket, I have been looking for one...mainly for bending the sides.
I have used French polishing in the past. I was concerned about getting the back and neck to a mahogany-red color, and was wondering about how to do that. I haven't had much luck with dyes since they tend to leave a blotchy finish. I have used Stew-Mac red lacquer spray in the past with some success. I don't want to put too heavy of a finish on it.
Also, I have an bridge on order from Bridger Products (Vern Brekke). It is adjustable but works without thumb screws, so I think it will look pretty nice with this old mandolin.
I was able to separate the old tailpiece from the armrest that was added later in life. The tailpiece is a cloud-type, but with only three leaves, rather than seven. I think it may be original because there is no evidence (by way of the screw holes) that the tailpiece was ever replaced. I realize that every picture of an Alrite has the seven-leaf cloud tailpiece.
Anyone have an original looking pickguard that they want to part with?
Finally, there is an Alrite listed on Ebay.
Celluloid pickguard material is available from www.axinc.net. They have the best stuff I can find these days. If you order from them, be aware that there is a $32 hazardous materials fee for shipping celluloid. It is a flat fee, so it doesn't matter if you order one piece of binding or 20 lbs. of pickguard material. My suggestion therefore is to place a sizeable order, then it won't sting so much.
By the way, don't blame them for the fee. It has been required by the government and UPS ever since 911, when they decided that celluloid is flammable. Axiom does not make a profit on the fee.
I've never had any problem with alcohol soluble aniline dye. You can avoid blotchiness by applying it to wood that has been wash coated with thin shellac, or mix it directly with the shellac itself. Always use pure grain alcohol, never denatured alcohol. If you do apply it directly to unsealed wood, apply it lightly, follow it with a rag dampened with alcohol, allow to dry for quite a while, then repeat as necessary. Make sure the wood is very well sanded and very well cleaned of sawdust.
You can get several grades of colored oil varnish from a violin supplier. You can add a few drops only of Japan drier to the varnish to reduce the curing time.
Jim
My Stream on Soundcloud
19th Century Tunes
Playing lately:
1924 Gibson A4 - 2018 Campanella A-5 - 2007 Brentrup A4C - 1915 Frank Merwin Ashley violin - Huss & Dalton DS - 1923 Gibson A2 black snakehead - '83 Flatiron A5-2 - 1939 Gibson L-00 - 1936 Epiphone Deluxe - 1928 Gibson L-5 - ca. 1890s Fairbanks Senator Banjo - ca. 1923 Vega Style M tenor banjo - ca. 1920 Weymann Style 25 Mandolin-Banjo - National RM-1
[QUOTE=rcc56;1649382]Celluloid pickguard material is available from www.axinc.net. They have the best stuff I can find these days. If you order from them, be aware that there is a $32 hazardous materials fee for shipping celluloid. It is a flat fee, so it doesn't matter if you order one piece of binding or 20 lbs. of pickguard material. My suggestion therefore is to place a sizeable order, then it won't sting so much.
I had in mind something more complete..like a vintage piece with the attachment hardware.
Interesting that you mention all-grain alcohol. I just watched a video about mixing shellac (O'Brien...Lmii). He said the same thing about the difference between alcohols. He uses Everclear.
Jim,
My cover is very plain, but shaped like yours. It was soldered to a large piece of brass to form a crude armrest. I took it to a machine shop and they popped it off with a lot of heat.
[QUOTE=Tukanu;1649390]An original Gibson guard is getting hard to find and expensive. Be prepared to spend over $125, quite a bit more if it's got the nice cam clamp. Be careful; a lot of those old guards are now turning to powder, and the gas they release when they decompose might damage your pretty work.
I found out the hard way that denatured alcohol reeks havoc with colors and can cause drying problems. I can't get Everclear around here, so I use Golden Grain. Sometimes the guy at the liquor store makes a smart remark. I just tell him that if I wanted to drink it, a pint or a fifth wouldn't be enough.
I made an accurate drawing of the pickguard on my Alrite. I can e-mail you a scan if you like.
Tony, that would be much appreciated.
David
I sealed the mando with shellac and filled the mahogany neck with a water based filler. I got the lacquer color coat and a couple of clear coats on when the garage warmed up to 65F. Supposed to be warm again tomorrow, so I can get a few more spray coats on.
A couple of posts back, rcc56 has some great advice on finishing. I would have followed his advice, but I had already purchased the lacquer spray from StewMac.
Here is the front and back after a few clear coats:
Looking good.
I never fail at anything, I just succeed at doing things that never work....
Fylde Touchstone Walnut Mandolin.
Gibson Alrite Model D.
"It aint over until the flat lady sings".
10 light coats of satin lacquer, leveled with 600grit, then a couple more finish coats of lacquer.
The tuners cleaned up with naval jelly.
I used an adjustable bridge, since I did not have the original.
I think the tailpiece might be original because there was only one set of screw holes.
Original cost was $340, and about $100 worth of new materials.
It is much louder than the A/N Flattop that I recently built. Tone is pretty clean. Done and done.
Lots of character there, very nice! Thanks for posting all of this.
-Dave
Flatiron A
Way too many other instruments
Looks great!... let’s hear it!!!
aka: Spencer
Silverangel Econo A #429
Soliver #001 Hand Crafted Pancake
Soliver Hand Crafted Mandolins and Mandolin Armrests
Armrests Here -- Mandolins Here
"You can never cross the ocean unless you have the courage
to lose sight of the shore, ...and also a boat with no holes in it.” -anonymous
Nicely done! I love these mandolins.
Larry Hunsberger
2013 J Bovier A5 Special w/ToneGard
D'Addario FW-74 flatwound strings
1909 Weymann&Sons bowlback
1919 Weymann&Sons mandolute
Ibanez PF5
1993 Oriente HO-20 hybrid double bass
3/4 guitar converted to octave mandolin
Most impressive, sir!
Steve
"They're approaching. That's very forward of them."
Lovely job
That is one Alrite job!
The mandolin is incredibly loud and the tone is fine. Very impressive. Lovely looking instrument.
Bookmarks