Search:

Type: Posts; User: Tavy

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Thread: Bowl back science

    by Tavy
    Replies
    10
    Views
    937

    Re: Bowl back science

    I think it depends - certainly that is a "mode of failure" for Neapolitans, this is not to say there isn't downward pressure on the top though, and of course US bowls with their less arched tops tend...
  2. Replies
    9
    Views
    361

    Re: Strap for bowl back

    A few ideas here:
    https://www.youtube.com/watch?v=mlnUGKXjWJE&t=28s
  3. Thread: Bowl back science

    by Tavy
    Replies
    10
    Views
    937

    Re: Bowl back science

    Thanks Tom: they do sound good, but mostly I can't help but think that I'm hearing the room as much as the mandolin. I also just flat out disagree with the line that "Most mandolins play sharp on...
  4. Replies
    27
    Views
    667

    Re: 14” octave string set questions

    +1 on what others have said, you're going to need a ships cable on that low G. Good luck with the fingering!
  5. Thread: Bowl back science

    by Tavy
    Replies
    10
    Views
    937

    Re: Bowl back science

    In addition to what Dave said, I would say that the paper is strong on measuring, and short on conclusions ;)

    They did note that the bowl has effectively no contribution to the resonances, that...
  6. Replies
    17
    Views
    544

    Re: Best way to test preamp sounds at home?

    I'd reiterate what others have said - plug the instrument and preamp into a recording interface, and either monitor directly via headphones, or record and playback. You could even compare directly...
  7. Thread: Bowl back science

    by Tavy
    Replies
    10
    Views
    937

    Bowl back science

    Interesting to see someone investigating the science of bowlbacks https://brill.com/view/journals/ijwc/2/1-3/article-p1_1.xml
  8. Replies
    21
    Views
    1,304

    Re: Demonstrating a mandolin

    From someone sitting on the selling side of the fence this is all good interesting stuff, so thanks for the tips ;)

    Seriously though, some of us do worry about how to adequately demonstrate stuff...
  9. Replies
    10
    Views
    610

    Re: Streaming services for acoustic/mando music

    Not sure if this works when driving... but I'd give a shout out for FolkAlley and indeed the many other "curated" services out there, if only because they do force you to listen to new stuff from...
  10. Replies
    20
    Views
    1,049

    Re: Most tunes I post to YouTube are 65+ years old

    Me neither, and I'm in the "nut enough data" range as well.

    I was moderately surprised (and somewhat pleased) that "How to Hold a Bowlback Mandolin" is my most viewed though.
  11. Replies
    5
    Views
    444

    Re: A Pair of Ceccherini's

    Other way around, the older 24 fret one has the English label with the serial number, the Italian label without the number is on the newer 22 fret one.



    Yes same size.



    Haha, I've had a...
  12. Replies
    5
    Views
    444

    A Pair of Ceccherini's

    One of these I've been playing for while, the other is newly restored, not often you get two of these in the same place at the same time!

    In addition to the level of decoration, the main...
  13. Thread: Metallic Sound

    by Tavy
    Replies
    3
    Views
    463

    Re: Metallic Sound

    Lots of reasons: poor setup, badly shaped/crowned frets, poorly cut nut or saddle slots, poor neck setup and action. Then if you think of "metallic" as the opposite of "rich", you're looking for...
  14. Re: K&K body noise and picking technique - novice question

    The issue is your hand touching the thing that the K&K is attached to (the top) so yes if you planted your pinkie on the pickguard rather than the top then that should be fine.



    Resting the...
  15. Replies
    9
    Views
    733

    Re: End Block question

    Don't try that on a cast tailpiece, you'll be there for a long old time!



    +1, unless you like to live really dangerously ;)
  16. Replies
    5
    Views
    539

    Re: Cleaning up headstock veneer

    Indeed, I would start with micro-mesh as you may well find that 2400 or if pushed 1800 micro mesh are coarse enough to do the job, then sand through to say 3.6 or 4K and buff. It'll be a small area,...
  17. Replies
    9
    Views
    733

    Re: End Block question

    For any mandolin I can think of, except some vintage bowlbacks and flattops yes. Note you will need to enlarge the hole in the tailpiece to match - that is actually the hard bit - find yourself a...
  18. Re: Identifying problem with newer Gibson cremona Rush

    What John said: likely the nut either binding, or from what you're saying, maybe a chip off the front of the nut, so that strings in tune open, are out of tune when fretted. Something to double...
  19. Thread: Reverb Pedals?

    by Tavy
    Replies
    12
    Views
    1,290

    Re: Reverb Pedals?

    The HOF pedal is great, but eats batteries real fast (so you'll need a power supply to go with it), I've stopped using mine because any desk I plug into has arguably better effects anyway...
  20. Re: Removing Adhesive Residue - 1930s Regal 'Custom Built'

    +1 on keeping it mild: if it's a varnish finish, then not many glues will stick to it too well anyway, so the residue should sloth off with a bit of polishing, maybe even a fingernail, and then...
  21. Re: What would you pay for this Meinel & Herold bowlback?

    These are bar frets, they often get quite skinny/low after multiple dressings which means they bend super easily. So the last fret here is bent up on the right hand side.



    Amen, that did make...
  22. Replies
    9
    Views
    679

    Re: Washburn bowlback bridge

    It was - sadly not mine!
  23. Replies
    9
    Views
    679

    Re: Washburn bowlback bridge

    I respectfully disagree - what's on there now is a horrible solution - it's not well fitted so the sound will not be as good as it should be, and it doesn't distribute the load evenly across the top,...
  24. Replies
    7
    Views
    755

    Re: Brunh Mandolin truss rod help

    I'm not too sure what I'm looking at there, but that's round: it doesn't look to me like it was ever designed for an Allen key. Could it have once had a nut on the outside maybe?
  25. Replies
    18
    Views
    1,098

    Re: String tension & neck stability question

    I used a special POT sold by axesrus which a quick search suggests they no longer have :( It's actually 2 stacked POT's, one is active in the 0-5 position, and one in the 5-10 with a centre ident. ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4