- Liquid Ivoroid
- String slot in nut too low
- Honest wear
- grain direction question
- Purpleheart?
- Getting more volume out of your mando
- intonation
- those last 6 F-5 frets
- Benefits of Banjo frets
- Harvesting an Engelmann Spruce Windfall...
- Which glue?
- Mandolin design questions
- Spruce Wood
- How Best to Clean Tailpiece Cover?
- Good Reads
- binding gluing failure
- Volume drop off question
- Pine pitch, pine sap
- Which chisels to buy
- classic designs REUSED and REPRODUCED
- numbering instruments
- signature
- Medulary Rays
- how do I get started
- Building a mold
- Fingerboard Extension
- Endgrain finishing treatment
- Tell us about your favorite Repair Guy
- replacing nut
- Bargain for Nut Slotting File
- Nut Problems
- Bridge Theory
- Adjust bridge for intonation
- New Collings MF5 V
- Custom string length fretboards
- Ovation action lowered
- X-bracing an F4
- fret slot spacing
- Conical fingerboard
- Finish pitting...
- travel instrument prototype
- Homemade Tuning Buttons.
- Wolf tones
- Scraping binding
- Multiple layer bindings
- string tuning problem
- reversed s style waverlys
- reversed s style waverlys
- Quick and Dirty
- Installing a radiused fretboard
- multiple pieces
- neck joints
- Action
- walnut sides - how thin can they be?
- Mandolin workshops have returned
- Problems in the finishing steps
- the name game
- Info on a builder in Maine
- heating a pipe on bench saw - any concerns?
- bridge for e mando?
- Safe-T-Planer
- A Design Question
- Source for Tonewood
- String breakage
- Varnish Problem
- wetting long side slats
- Tuning machines
- Repairman in 93454 area
- Binding Higher than Slot
- Loose tuner button
- preparing bone for use
- Head and tailstock material
- waverly confusion
- Bridge String Spacing
- Meet Bill Collings
- Another IV kit newbie
- Builders in North Carolina or Virginia
- Heard of this builder?
- Single foot Loar-style bridge
- Undoing a Titebond Joint
- "F" hole backing cloth
- IV mandolin kit arrived today
- Tuniing-gear problem?
- Weber buzz
- IV kit and tools
- Truss rod access
- Router tearout repair
- Vintage Tuner
- Sanding with 100 grit to remove machine marks
- Do you make inside forms smaller?
- Duplicarver Holding Fixtures
- Bending over back woods
- Carved top with flat back
- Tulip Instruments
- Luthier in Memphis area?
- A Oval Neck placement
- Burn-throughs in the french polishing process
- DMartin A style Mando bridge
- Recreation of Gibson blacktop
- Recreation of Gibson blacktop
- Flat to radius
- cutting Corian
- setup question
- bracing patterns
- truss rod versus carbon fiber
- Fancy woods
- Donate Your Skills to an Elementary School!
- HELP!
- Score!
- Tonebar material
- Dremmel as thickness planer
- A few questions
- KTM-9
- Stage one of my heat bending system
- Bowlback repair pics
- New bushing sizes for Schallers!?! BEWARE BUILDERS
- Aftermarket Headstock Inlay
- Wannabe builder now needs to be a repairman
- Bought my first scraper today
- Insect Attack
- Dudenbostal building Thile's mando
- tuning key restoration?
- Wagner Safe-T Planer burns wood
- Stain first or seal first
- crack in top
- Alternative Binding
- Adjusting my Gibson Bridge
- IV Kit
- Tap Tuning
- Acrylic paint instead of MOP inlays
- How often do pros need to refret?
- Double checking
- Dovetail
- Step routing.
- Neck Joint
- Wood thickness on plates differences with differen
- Fret marker removal
- Converting a Baritone Uke
- Changing A Tail Piece
- fingerboard
- Repairs gone bad
- Yet Another Loar Plan
- Fretwire
- Luthier schools for mandolins
- Block inlays
- Intimidated and overwhelmed
- Adzes
- Best way to thin soundboard on IV kit
- Clock Mainsprings
- how best to fix....
- setup!
- drilling for tuners
- Carving by feel
- Finishing the Scoll?
- Carbon fiber neck rod installation..
- loar bridge/string break angle
- IV kit gone
- The Macassar Madness Mandola
- Mandolin bridge fitting
- Sharpening a convex finger plane
- Stainless Steel Frets
- tail piece question
- Deet (insect repellant) reminder
- Replacing fret board
- Distressed
- Sound Hole in Mandolin Side?
- simple inlay tools
- Gotta duplicarver or cnc?
- another inlay question
- Advice on warped neck
- Intonation
- Truss Rod
- cremona bowl back
- Piccolo sized bodies
- Need a little help on applying finish
- cheap and easy
- IV Kit doesn't implode
- End Pin
- Filling Rosewood Binding
- Position markers
- F4 VS F5"
- Wood Binding
- Question on Radius vs. Flat...
- mandola case
- Buffers
- Bridge question
- half and half
- How much binding stock to I need for an A?
- truss rod covers for eastman
- Fret buzz
- upcoming workshop
- A Question of Finish
- Someone to Re-finish Old Gibson F4
- Dudenbostel on DIY Channel
- "A" string problems
- tone woods
- How to lower ebony bridge?
- Help choosing mandolin kithttp://www.stewmac.com/s
- IV Kit Bridge
- Volume of a Mandolin
- Mandocello K4 style buiders
- binding size for IV kit peghead
- Refret and vintage value...
- clear pickguard
- End Pin/Strap Button Pulls Out all the time
- Boiling strings
- test
- wood imperfection?
- picture i hope
- Interesting situation, reshaped neck
- The Woodshed
- From Guitar to Mandocello...
- Building a case(s)
- question about inlay
- showing my ignorance
- Truss Rods
- Nuts
- Bowlback restoration project
- Buy a Dude or Build a shop
- PING: Paul Lestock at Arrow Guitars & Mandolins
- asymmetrical plate graduating
- Bowed Neck
- Resonator project?
- Martin Back Packer Mandolin
- Mando Bass
- how thin?
- Adirondack or Engelmann
- Any thoughts on the Orrico tailpiece?
- broken neck repaired
- Construction grade Yellow Pine
- Fiber Binding
- pickguard for collings MT2
- aniline dyes
- Lacewood?
- Pearl nut vs bone/ivory saddle
- Bridges
- something safe to protect finish
- Wood binding thicknesser
- Flariron Performer A neck issue
- Supplies
- String lengths (slightly off topic)
- 20's Gibson pickguard mount
- Slotted peghead
- binding neck or not
- Can anyone direct me to a picture of a mandolin
- New problem
- Putting bigger frets on a mando
- frets
- Violin Repairman for an old Gibson Mando?
- Grover Ebony Button Prototypes