- Tuning Problems with my E-string
- mic in the wind
- What fretboard radius is most common?
- string angle from bridge to tailpiece
- flat top mandolin cave in
- cleaning/repair of finish?
- Filling grain in walnut.
- removing bridge
- New frets and nut job
- Inlay on arm-rests
- a little advice required
- Ethics - whine - or bite the bullet?
- advice on building oval hole mandolins
- Unbound Mandolin
- Building a case
- Making my neck
- A vrs F
- Bridge Tips Forward on String Change
- What is the easiest and cheapest way to
- security for end pins
- New Tailpieces
- greetings and crazy questions
- Strings
- What's the difference between a flat top and
- Removing Finish on Neck
- Knot in a bad spot
- Stainless Steel Fret Wire
- marking bridge
- Looking for Mahogany
- bone or ivory
- graphite
- Making An Archtop Guitar
- Latest Newell mandolin
- Refinishing
- Now THIS is a repair!
- spruce, willow or mahogany blocks?
- Waverly Tuners Again
- Electric Mandolin Neck
- Electric Mandolins
- GAL Anyone?
- To glue or not to glue?
- Gibson A Replacement Tuners
- Grain count and straightness
- Tuner Help
- how would you spruce things up?
- Bare wood...
- GUITAR PROBLEM
- Vega bowl back
- All mahogany mandolins?
- Oil varnish or spirit varnish ?
- kudos to Allparts
- Bracing question
- Sealer for lacquer chip?
- Two Piece Necks
- tuners tune up.
- Vintage F model question- Help!
- Nowhere to learn
- Cocobola for a back?
- Nut slot size?
- Loose nut
- Bridge making
- fingerboard extensions
- Mandolin Finish
- Regrading a Pac-rim
- Regrading a Pac-rim
- How to make a Johnson MA-100 Sound Good?
- Chris Thiles, Dude
- From lacquer to varnish
- Varnish Basics
- Gibson neck joint
- Mandola repair - help needed
- Sunken tops on flattops
- Ringing harmonics
- moment of truth
- Thinking about Building My First
- BRIDGES
- just sanded off my varnish...
- Cuban Mahogany
- Calling wood identifiers....
- Body Depth? What are the effects?
- Intonation question
- Anyone ever used an ebony nut?
- instrument info
- headstock repair
- Cleaning off a Goopy Mess
- Chipped binding on Aria Pro II
- Building a Stew-Mac F5 Kit
- Gibson with bolt on neck
- thank you
- what tools to carve a top?
- Info required on builder
- Nut Cleaning
- Bridge compensation specifications
- best finish for koa
- Compensated bridges
- saddle notches
- Harlan #2
- proper neck relief and humidity
- tap tone for different body shapes
- Nut slot is too deep
- Neck tension/bowed neck
- Dovetail Cutting
- Liquid hide glue
- An unintentional reward?
- Removing glue spots from finish
- tuner upgrade for Morgan Monroe
- Mandolin Capos
- Easy made scroll saw for cutting pearl.
- Pugasus Color
- where to clamp and how?
- Cutting MDF with planer
- Octave Mandolin w/Resonator?
- Liberty cnc machines
- Washburn M3SW problem
- Wood binding
- Crack in the back
- Heat Bending Pictorial...
- Varnish Curing TIme
- radius fingerboard
- Floating Tailpiece for mandolin ?
- What is 12 minus 8?
- Warped sound hole
- Thickness calipers
- new builder
- High humidity
- Best Mandolin Rim Form Designs
- Another radiused fretboard question
- Re-finishing a 1936 Gibson L50 like mando
- Bubbles and Blisters
- Drop D Tuning
- Endpin installation
- LMI rubber heating blanket
- Siminoff's new plans....
- Wanted - How to reset a neck
- Gluing teak
- Banjolin Bridge Needed
- Birds Eye Maple
- Water soaked wood?
- backs
- Finish on a water based stain
- compensated fingerboard
- intonation problem
- Resonator Set- up
- Check out this wood!
- Tamarack for a mando top?
- how to put on a pick guard
- Loose end pin
- Tuner problems- replacement Please help
- Thickness of Scroll area? Miffed
- How to add strap hardware
- Selling your "first-born"
- vintage fret smoothing?
- how much is too much radius fingerboard/fret size?
- Never had this happen to me so intensly.
- Bridge repair-Old Gibson A
- Gibson Pick-guard
- Gummy Neck
- Looking for Ward Elliott
- Please help--
- Fall classes now forming
- tap tuning
- Buzz, please help
- Scroll Binding
- Looking for mandoline builder adress
- cleaning up vintage instruments
- Quilted vs. Flamed
- body outline changes
- Side binding
- scroll screwup
- repairing cracks
- 3rd mando finished
- New Gibson Master Models
- Tru-Oil vs Deft vs Shellac?
- Stewart MacDonald kits
- mesquite wood
- Horizontal shaft tuners
- Question About Modification
- I need repair help
- Need refret job in Texas
- Changing Fretboard
- fret board
- Repair in Georgia?
- Ebony, pau-ferro, etc
- Gibson A-Jr tailpiece
- set up
- Red Spruce Stain
- This has some great pictures of wood species
- Trying to get a hold of Ron Oates
- How come some builders are so good... so fast?
- I'm a bone Head!
- Spray Room/Booth Ventilation
- Detailed specs for tailpiece
- Backs
- Will the holes line up?
- newer cast tailpieces
- plate shape
- re-gluing brace
- Binding a new mando
- Radiused fret board
- Building a prototype
- Mando vs Beach
- Flame/Curly Maple
- Flat lacquer finis
- FFts
- Los Angeles Mandolin Luthier ?
- fret problem
- One Piece Back, Which direction the grain?
- Cherry
- Experimental woods
- Holst Instruments?
- McIntyre mf-200 feather pickup
- best way to dissolve celluloid
- Replacing the String Nut
- Gibson A-Model Finish
- What defines wood quality?
- dual truss rod supplies
- radius fingerboard
- Self-taught or Mentored?
- Solvents for French Polishing
- Mandolin Making Workshops
- Spruce in the oven
- Caring for a varnish finish
- Attn. TOM ELLIS
- Carpenter Jack
- builder / players
- Custom Exotic Wood HELP!
- Tuner Problem
- What's the best way to add radius to...
- Rebuilding a pac rim
- How to slim down a neck
- Binding Repair
- Custom engraved truss rod covers?
- Older 74 F5 no guts
- Ebony Buttons
- should'a used hide glue
- Custom Binding
- lacquer
- Videos
- Upper cap on headblock
- sake
- Stamping/Engraving tailpiece covers
- String Spacing
- thickness
- WOOD
- Paper Shim
- Help!
- Flying V acoustic mandola
- Want an Octave?
- Ohhh no...
- Don Kawalek