Results 1 to 12 of 12

Thread: Six string guitar conversion - Tenor Guitar

  1. #1
    Still learning Taylor and Tenor's Avatar
    Join Date
    Sep 2008
    Location
    Cape Cod
    Posts
    241

    Question Six string guitar conversion - Tenor Guitar

    Has anyone ever tried to convert an inexpensive 1/2 or 3/4 size 6 string guitar to a tenor guitar by removing the 5th A string, replacing the A string with an additional E string close to the 6th string by adding an additional string peg hole between the 5th & 6th and cutting a new slot in the nut?????

    Thus making a tenor guitar (DGBE) with two E strings on the bass side mandolin style/width. I want a tenor guitar with a space after the 4th string and then two bass E strings.

    Thought it might make a fun project.

  2. #2
    Registered User Greg Ashton's Avatar
    Join Date
    Sep 2002
    Location
    Burlington, Ontario
    Posts
    130

    Default Re: Six string guitar conversion - Tenor Guitar

    I don't think I would consider what you're describing as a tenor guitar but I've seen Baby Taylors converted both to single strung tenor guitars (GDAE) and double strung octave mandolins (GDAE). Also, I've done the modification you described on a $100 Seagull parlor guitar a few years ago. I think I tuned it DD GDAE. It proved to be too frustrating because of intonation issues so I abandoned the idea.

  3. #3
    Confused... or?
    Join Date
    Dec 2008
    Location
    Over the Hudson & thru the woods from NYC
    Posts
    2,927

    Default Re: Six string guitar conversion - Tenor Guitar

    Quote Originally Posted by Cape Cod Struggler View Post
    ... by adding an additional string peg hole between the 5th & 6th and cutting a new slot in the nut?????
    I forget where on-line (I think one of the Cafe's luthier members), but I recently saw a standard guitar converted to a Roger McGuinn-style 7-string (w/ octave 3rd/G string, as on a 12-string) by adding a banjo tuner to the middle of the headstock. Slick idea and Very clean looking!
    - Ed

    "Then one day we weren't as young as before
    Our mistakes weren't quite so easy to undo
    But by all those roads, my friend, we've travelled down
    I'm a better man for just the knowin' of you."
    - Ian Tyson

  4. #4

    Default Re: Six string guitar conversion - Tenor Guitar

    I have done the conversion on a Little Martin and it seems to work fine. I just removed two strings, retuned a bit and ended up with GDAE. I think you can figure it out. I tried this on a 3/4 inexpensive guitar, and it worked fine, but when I tried to re-string I had major intonation problems.

  5. #5
    coprolite mandroid's Avatar
    Join Date
    Oct 2002
    Location
    Outer Spiral Arm, of Galaxy, NW Oregon.
    Posts
    17,103

    Default Re: Six string guitar conversion - Tenor Guitar

    Martin sells little martins with tenor necks, new.
    writing about music
    is like dancing,
    about architecture

  6. #6

    Default Re: Six string guitar conversion - Tenor Guitar

    Martin does sell the "Little Martin" tenors, but my recollection is that they were about $200 more than the regular guitars. I picked mine up because I got a good deal on it, but probably wouldn't have paid much extra. As is, if I get the bug to convert back , I can. Also, I've played the converted instrument out quite a bit, and no one has ever even mentioned that it only has 4 strings. Not very noticeable unless you really look closely.

  7. #7
    Still learning Taylor and Tenor's Avatar
    Join Date
    Sep 2008
    Location
    Cape Cod
    Posts
    241

    Default Re: Six string guitar conversion - Tenor Guitar

    Martin Tenor guitar street price is $449.00 vs Martin LX (HPL top) at street price at $279.00.

    I ordered a Fender parlor (3/4 size) 12 fret guitar on clearance for $99.00. If it works out, I will reduce the width of the neck and hope the neck stays straight. But with only the pressure of four strings it should be fine based on a child's 3/4 Strato style electric guitar I converted to an octave mandolin and cut down the neck width.

    BTW, the Strato Mando will over power any banjo I encountered and sounds great.

  8. #8
    Registered User
    Join Date
    Oct 2005
    Location
    citrus heights ca.
    Posts
    348
    Blog Entries
    1

    Default Re: Six string guitar conversion - Tenor Guitar

    Yes I reduced the neck of a garage sale guitar and removed to tuners. took off the i=6 strings and retuned GDAE It has a nice deep sound
    fred davis

  9. #9

    Default Re: Six string guitar conversion - Tenor Guitar

    have you thought about using a baritone uke?

  10. #10

    Default Re: Six string guitar conversion - Tenor Guitar

    I have a Mandobird that I love playing. I can play it tuned in standard mandolin GDAE or to rock out, I tune it to EADG, but the intonation is then out a bit, worse as you go up the neck. i tried tuning to DGBE, but it just doesn't cut it. I thought about buying a second one to optimize intonation for EADG. I think that could work.

    Along these lines, I also picked up a mini 6-string Flying V clone with a built in min-amp and speaker, got it at Big Lots for $60. It took me about 3 hours to fix all the quirks, to get it to intonate and play as a cheap guitar, but for $60, I can experiment with it and see what works, etc. This ax does not tune well to standard guitar tuning, it's too slack and won't intonate. If I tune it up an octave, it breaks strings way too easily. So, I drop everything down a fifth (e.g. E > A, A > D, etc). It was a bit of a stretch to intonate, but it works good and feels much better. If the tuners were any good, it would be a nice liitle guitar. So here, my idea was to swap the strings upward, so the 13 on B goes to high E position and drops down to an E lower for standard tuning. But this thread makes me think it might convert well to a 6-string mandolin, with either double E and A strings or octaves on the G and D strings, either way for the "jangle". The later option might be cool because then I can get the single strings on high for riffing guitar solos.

    I like the ideas in this thread and am going back to try a few things I've read here. One is to convert a 7-string Fender that I never got used to into a McGuin 7-string, as described above. Never heard of that until this thread. Thanks for sharing! I just need to make a new nut and mod the bridge a bit. I have a machinist friend who can help me with this part.

    Back to the Mandobird, there's a YouTube video of a guy who converted his Mandobird to a UkeBird. Works good for him. I also have a baratone uke that I just love to play and have been thinking of a Mandobird tuned so, but the tension is not right with the factory strings. From what I can tell from all this mini guitar to uke or madolin conversion, is that there is a string diameter to length ratio that determines the pitch. I would rather have the baratone version MandoUke myself, so I'll experiment with the strings to see what can be done. Does anyone know of a reference table online or a formula for calculating string diameter to length to pitch? I guess I could do a matrix of my known pitches (Hz)/diameters (in/mm)/lengths (in/cm) and see what I get.

    Nice thread for us tinkerers, thank you all for sharing!

  11. #11
    Registered User
    Join Date
    Sep 2002
    Location
    Chicago - most lately but - home is in Northern Arkansas.
    Posts
    606

    Default Re: Six string guitar conversion - Tenor Guitar

    Bari Uke to Tenor ... What seems to work is getting a set of good classical guitar strings and then restringing and tuning the instrument. I've done this with a few tenor Uke's, haven't tried it with a bari (yet). I have two really old Bari's in the basement but time has pushed it to a far back burner.

    My preference was to go to Aguila strings - in one of the many iterations. I went to first standard tension then tried the 'Hard' sets while watching the bridge, neck, top for deflections of defections. It flat out works! Somewhere on this thread is one I started called 'Tiny Tenors' where I went into the math of the strings. After experimenting and trying to find the various tensions, I just went with the actual thickness and it worked. A Bari is normally a 19 inch scale whereas a Tenor Uke is 17 inch. With the classical guitar strings, tuning it to CGda was no problem. There may be an issue if you are trying to get it into GDae tuning. That High E string might not be a possibility.

    Oh yes - for concert Uke Players / owners ... Aguila is now listing a set of strings for GDae ... Concerts have a 15inch scale. This is a really small company in Italy - but the importers may listen and offer fifth tuned set for Tenors and or Bari's. It doesn't hurt to ask ...
    Mandola fever is permanent.

  12. #12
    Oscar Stern s11141827's Avatar
    Join Date
    Jul 2019
    Location
    2486 Govoners Drive South
    Posts
    433

    Default Re: Six string guitar conversion - Tenor Guitar

    Quote Originally Posted by Greg Ashton View Post
    I don't think I would consider what you're describing as a tenor guitar but I've seen Baby Taylors converted both to single strung tenor guitars (GDAE) and double strung octave mandolins (GDAE). Also, I've done the modification you described on a $100 Seagull parlor guitar a few years ago. I think I tuned it DD GDAE. It proved to be too frustrating because of intonation issues so I abandoned the idea.
    An Electric Guitar style intonatable bridge would help

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •