Search:

Type: Posts; User: sunburst

Page 1 of 20 1 2 3 4

Search: Search took 0.20 seconds.

  1. Replies
    6
    Views
    1,132

    Re: The Gibson Factory in Kalamazoo

    A lot like one that I used to shape a bunch of banjo necks too. Big ol' cutter head right up there in the air, 7 HP motor spinning it...
  2. Re: Neck Reset for Flatiron Army-Navy mandolin

    Is it bolted? (hardware joint)
  3. Replies
    8
    Views
    639

    Re: Instaalling frets on a new build

    With guitar builds I fret after gluing the board to the neck and setting the neck in the body, with mandolins I fret the 'board before gluing to the neck/extender.
    I can't really give you a reason...
  4. Replies
    2
    Views
    318

    Re: Wyatt Ellis debut album

    Just saw Wyatt perform Monday in Lexington at Woodsongs. Impressive young man, good music.
  5. Replies
    51
    Views
    2,704

    Re: Keeping up with the Fiddlers

    You might try asking the fiddlers to slow it down a little, explaining that you are a "relative newbie". As you gain experience speed will improve, but until then a little courtesy from others...
  6. Thread: Buzzy note

    by sunburst
    Replies
    27
    Views
    903

    Re: Buzzy note

    The OP said If it was an adjacent low fret there would almost certainly be at lest one more fret where the rocker rocks. I suspect it is one high fret, and if it won't drive down filing level is a...
  7. Thread: Buzzy note

    by sunburst
    Replies
    27
    Views
    903

    Re: Buzzy note

    Make that "don't over do it".
    (I hate when spell check misses things like that.)
  8. Thread: Buzzy note

    by sunburst
    Replies
    27
    Views
    903

    Re: Buzzy note

    The goal is level frets. If the offending fret is high and can be driven down without undue force, then that is a good repair. IF the fret cannot be driven down without undue force don't hit it...
  9. Replies
    9
    Views
    773

    Re: Can I say tap-tuning on MC?

    Dana is successful in making good sounding guitars, so his methods don't need to be called into question, but his explanations of what he is doing are based on conjecture rather than measurements,...
  10. Replies
    9
    Views
    773

    Re: Can I say tap-tuning on MC?

    There is much info out there about tap tuning, much of it inaccurate, some useful.
    Suffice it to say that it is not necessary to "tap tune" in order to make a good-sounding mandolin. Many builders...
  11. Replies
    5
    Views
    619

    Re: Sourcing Archtop Spruce Billets

    You might try Randy Lucas.http://www.lucasguitars.com/
    I don't know if he has archtop billets but he's a great guy and I've known him to have good quality wood in the past.
    (I assume you've tried...
  12. Replies
    53
    Views
    7,228

    Re: Neck reinforcement vs a truss rod

    Maple.
  13. Replies
    53
    Views
    7,228

    Re: Neck reinforcement vs a truss rod

    Still the case, though guitar building has mostly overtaken mandolin building around here lately, so that's different.
  14. Replies
    53
    Views
    7,228

    Re: Neck reinforcement vs a truss rod

    My adjustable rods weigh 23 grams, my filler stick is spruce. I haven't done the math, but replacing maple with spruce offsets the addition of steel very slightly. Given a choice, I would prefer to...
  15. Replies
    36
    Views
    2,006

    Re: Lutherie as an art form

    While I think of my instrument making as being only slightly "art", there are those who tell me I'm an artist and consider my work to be art. Not an uncommon situation for someone who does this sort...
  16. Replies
    26
    Views
    1,998

    Re: Effect of bridge breakover angle.

    Richard500 is correct (as usual). Dave explained it more or less this way:

    The "top" of a banjo in the head. When it is tighter it is stiffer, so tightening a banjo head makes the top stiffer....
  17. Replies
    10
    Views
    484

    Re: String buzz caused by low nut?

    1/16" is good as long as the neck and frets are in good shape. I still suspect fret problems.
  18. Replies
    36
    Views
    2,006

    Re: Lutherie as an art form

    I read a book quite a few years ago. I wasn't overly impressed with the book (and much less with another in the series that i gave up on), but it made me think of art, what art is, what art is not,...
  19. Replies
    10
    Views
    484

    Re: String buzz caused by low nut?

    'Melt' is correct, low nut slots cause buzzing of open strings.
    What is your action height? I don't know nor need to know who dressed the frets, but I suspect something was missed. Good frets,...
  20. Re: New mandolin player - Loar 600VS - Clean inside the scroll?

    :disbelief:
  21. Replies
    26
    Views
    1,998

    Re: Effect of bridge breakover angle.

    Read post #12.
  22. Replies
    6
    Views
    448

    Re: Newbee with Tuner Question

    Loosening the gear screw creates added clearance at the tuner plates and makes turning easier, but it also causes lost screws and gears. Loosening the gear screws is a "quick and dirty" way to...
  23. Replies
    10
    Views
    877

    Re: Truss rod and carbon fiber.

    I did that in a quilted mandola neck, but the mandola is now somewhere far away so I don't know what the neck bow and/or adjustability situation is. Are any of yours where you can keep tabs on them?...
  24. Replies
    26
    Views
    1,998

    Re: Effect of bridge breakover angle.

    There is also quite a bit of added torsional load on the end block and associated structure of the body.
    Not a big deal, being a cheap mandolin. Makes it playable for the time being at least.
  25. Replies
    18
    Views
    1,272

    Re: Used gouges... (or new)?

    I have a gouge or two with missing ferrules and since I don't drive them hard with a mallet they're fine.
    If the handle with remove easily and you can find copper or brass the right size, you could...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4