Re: how to reseat a fret ?
I think a little water thin super glue would solve your problem. You will find the procedure in this Stew-Mac newsletter:
http://www.stewmac.com/tsarchive/ts0043.html
I would prep the board with wax, wick in the super glue as in the newsletter, then press the fret down with a piece of dowel for a minute or so.
Re: how to reseat a fret ?
I hammered all of mine in, as I didn't have a press. I also wicked a little thin superglue along each one as they were set to keep them from lifting. It's held for 7 months now.
Scott
Re: how to reseat a fret ?
What type of instrument are you making?
Re: how to reseat a fret ?
I built an ukulele (near scratch build). I am playing it now with some buzzing at higher frets. Fret#11 and #12 are visible higher at the center.
I installed the frets on the fretboard myself, by hammering the fret wires in, then cut the excess. This went really well. I should have added thin super glue at this phase but did not.
Before I finish the instrument, all the frets are flat down. After two weeks on sanding/finishing work, some of them pop up in the center.
I can't hammer them down at this time, it will damage the instrument. I had to press them down and the "Fret Jaws" sold by Stewmac won't work for the frets near the neck heel either. It's also too expensive, I am just a hobbyist and this is out of my consideration.
The main question is: what can I do to press fret#11 and fret#12 down ?
It took very strong "vise" action to press all other frets down.
Re: how to reseat a fret ?
Are 11 and 12 over the neck heel? Short extender (no more frets past the body joint, ukes are made with and without longer extenders)?
If those things are correct, you can rest the heel of the neck against something sturdy yet soft at the surface and hammer the frets with no damage. I use a shot bag (a bag of lead shot for folks who load shotgun shells, mine are #7 shot) to back up necks for fretting.
BTW, older instrument are re-fretted regularly, and nearly each time frets are installed on fingerboard extenders over the bodies of the instruments. There's no reason to fear damage from normal fret driving as long as it is done correctly with some kind of inertial mass to absorb the shock.
Re: how to reseat a fret ?
If a good deal are popping up I would first look at the width of the fret slot and radius of the wire. You could re-fret the problem areas.
As John brings up, it is important to confirm the type of instrument. Assuming it is a mandolin, there shouldn't be any problem hammering frets near the neck joint (be somewhat gentle). I hammer on mandolins every day. A good number of small taps will do the trick. Very slowly drive the fret down. Superglue is your friend here and will hold them down well, but it would be best to address the underlying cause first. Fretwork will almost always be needed after installing a pre-fretted board.
Re: how to reseat a fret ?
And see there... John was correct in first asking what type of instrument. :)
Re: how to reseat a fret ?
On post#5, I indicated it's an ukulele that I just finish building and start playing.
From the suggestions above, I will try to hammer gently on fret#11 and fret#12 so they go flat down, adding a bit of thin superglue to them. These two frets are right above the heel is where there is no firm support for pressing.
Re: how to reseat a fret ?
Reseating a fret can be a daunting task best left to professionals.
But now you to can easily master this task
with the help of me fret seating manual.
<Solicitation for commerce removed by moderator>
such a deal.
act now, a loose fret or two is like marbles rolling round inside head.
blessings
duh Padma