9 Attachment(s)
Moongazer Déjà-vu Electric Mandola kit
Hi Folks,
now to the other one...
I got a *big* Christmas present this year so I am not only the lucky owner of an Almuse Jazzmandolin since the forelast week, but I was also able to order this DejaVu Electric Mandola kit from Tom Morici @ Moongazermusic.com. Wanna give you some field report in this thread here... share pics, show the building process and so on...
Well, to say the truth I had some trouble with the shipping because the German toll hold the packet back and I had to pay 82€ trade sales...:crying: First I was kind of miffed but finally I entered that dough as my special private donation to avoid state bankruptcy :grin:
So I was very curious about what the kit would be like... :disbelief:
Attachment 81821Attachment 81822
I didn’t take photos from the accessories; it’s exactly as on Moongazer’s website except the Almuse Classic Humbucker I ordered. I missed just one thing – there is no screening foil into the set. I will definitely add some to prevent buzzing.
The body seems to be cut very accurately and had a careful pre-sanding. The neck (16,5'' with upgraded ebony fretboard) seems delaborated thoroughly and feels heavy and stable. Will be certainly a pleasure to play with :mandosmiley:
I pondered a lot about the design, I wanna give the instrument a hint of those pictures hanging into our living room:
Attachment 81824
Means that I’ll give it a graduated raspberry / crimson colour tone with silver on the edge that I will shape asland round the whole body.
While surfing around I found some examples that caused an order of a nice shelled maple veneer:
Attachment 81825
First I thought to veneer the whole surface, but the grain of the wood isn’t that bad especially at the left half – and I didn’t like the large black pickguard too much. So I finally decided to glue the veneer on a 4mm plywood and to cut a larger scratchboard out of it. I tried to simulate that just to get an idea of the form:
Attachment 81830Attachment 81826
The veneer will give the scretchboard some nice pattern (still have to decide which side and if asland or straight):
Attachment 81827Attachment 81828Attachment 81829
I’ll stain it in a lighter raspberry with some burst of orange around the orange stripe of the veneer itself. The body will be stained in some darker raspberry that tends to black at the body’s border. I’ve got quite much time for this because I’ll spray the finish into my garage and the outside temperatures should be around 20°C therefore. It may be pentecost until that...:sleepy: give you an update here from time to time...~o)
Have a good time,:cool:
Tom
Re: Moongazer Déjà-vu Electric Mandola kit
Keep us posted on the build. I've already got one of these on my Christmas list for next year!
Re: Moongazer Déjà-vu Electric Mandola kit
When I went to violin making school, it was customary to use a light colour wash of golden yellow on the bare wood then a clear base coat to seal the wood before applying coloured varnish....that way, the flip / flop irridescence of the figured wood was preserved.
Staining the wood itself can have a more spectacular effect when viewed from all angles but IMHO, the natural beauty of the wood is lost......might as well paint a pattern on........
Actually, that`s not uncommon......I saw a Chinese Strad copy with what looked like a gorgeous 2 piece flamed back - closer inspection revealed this was just a plain back with the stripes done in a darker lacquer ;)
Re: Moongazer Déjà-vu Electric Mandola kit
Very interesting thread. Thanks for keeping us up to date with your progress.
3 Attachment(s)
Re: Moongazer Déjà-vu Electric Mandola kit
Hi folks,
it's time to take stock of what went good and what went wrong until now.
I'm still pretty happy of the sanding, the shaping and the colours I found. On the other hand I obviously did not know enough about the woods I have to do with, especially about Alder (body). After the staining I recognized a couple of streaks along the body:
Attachment 84412Attachment 84413
First I thought they were splits, but then I learned they are natural color streaks which may normally occur in Alder. A darker stain would hide them. Additional a difference between Alder, Maple and Spruce (my testing wood) seem to be that maple and spruce keep the black prestain (worked really fine on neck and veneers) and alder didn’t, means that the black prestain completely washed out while doing the second stain with the crimson colour. On the result the measure was not really brought out and I had a dark washing stripe remaining round the edge especially of the backside (I stopped there with the last staining action and did not wish out round the whole edge, that was a mistake).
Well, I do not like the both effects too much so I will cut the scratchboards wider than I planned before, round the whole body until about 1cm inside the shaped borders to cover the problem areas. The veneers (just starting to finish them) look pretty good so I will be happy with this solution. (just hope I will not make so much faults with the finish... :crying:
Attachment 84414
But the awareness of this is that staining Alder may cause problems. If I did again I would finish it with a covering colour laquer instead of staining.
So long for today, thanks for reading,
Tom
Re: Moongazer Déjà-vu Electric Mandola kit
Once the weather warms up (for good this time) I'll be ordering a kit. I'm planning on using Re-Ranch products for the finish. Specifically, Re-Ranch Orange in a spray can. There is a great thread located here that covers one customer's project:
http://reranch.com/reranch/viewtopic...hlight=gretsch
My plan is to do the orange body, with an extra couple coats on the sides. Black pickups, chrome hardware and a pearloid pickguard. The only think I haven't decided on is the fretboard (ebony or maple).
Re: Moongazer Déjà-vu Electric Mandola kit
Orange body can't be wrong...
If you want to see what it looks like an orange body with a maple fretboard :
http://www.mandolincafe.com/forum/at...0&d=1318328082
and with a dark fretboard (not ebony but rosewood) :
http://www.mandolincafe.com/forum/at...6&d=1254389352
By the way, Tom's dark red color is very beautiful and original...
Re: Moongazer Déjà-vu Electric Mandola kit
Quote:
Originally Posted by
mando.player
The only think I haven't decided on is the fretboard (ebony or maple).
My neck with Ebony fretboard feels rather stiff and stable (and looks pretty good IMHO)... was important for my own decision. The dark orange in the Guitar Restoration thread looks very nice as well... good luck with it!!
Tom
7 Attachment(s)
Re: Moongazer Déjà-vu Electric Mandola kit
Finally!!! weather got warm enough and I had some time to continue my work with the Mandola... thought sometimes the day would never come :sleepy:
In the meantime while som rainy days I cut the scratchboard out of the veneer plates.
Attachment 85990Attachment 85989
Sanded the edges very carefully, and then I completely masked the front side and sprayed Mercedes Brilliant Silver spray twice round the edges, sanded with 1200 grit and sprayed again (in my garage, hanging down from the roof)
Attachment 85993
and this was the result after removing the tape (glad that I bought the expensive one - no adhesive remaining at all!)
Attachment 85994Attachment 85997
the silver edges were an important detail which loooks pretty good afterwards. Then I had to sand the plates again with 1200 grit. I had to do because I take a 2 component laquer now and I had to remove some spills of silver. The first coat of 1 component laquer was a bit thin and not all cavities were filled enough. After some testings with remaining scrastchboard pieces I decided to dry-sand with 1200 grit to remain dirty water from soiling the cavities. On dry-sanding I could vacuum-clean the fine rubbed-off parts. That worked quite okay and so I finally could give body and scratchboard the first of three coats of laquer yesterday...
Attachment 86000Attachment 86001
some tears running down on one of the scratchboard pieces... :crying: but what have I sanding paper for... wet this time. Now it'll be cold and rainy agein fpr several days so I must have a break again. But things develop that the Mandola could give its first tone two weeks after Pentecost... hopefully:mandosmiley:
so greetings to everyone who reads all this :grin:
Tom
1 Attachment(s)
Re: Moongazer Déjà-vu Electric Mandola kit
Hi folks,
just in the mood to give you an impression of what the instrument will be like... one day :whistling:
(click to enlarge)
Attachment 86029
I'll have some staining troubles until then, I guess... :crying:
more in a few days
Tom
Re: Moongazer Déjà-vu Electric Mandola kit
Just a notice today... i spent hours for the sanding-between after the second coat of laquer today... got out the tears quite well, I used some fine wooden sticks as sanding blocks and I drenched the sanding paper into warm water and a drop of dishwashing liquid one hour before sanding. I was careful the first time, but on the second spraying session I had an accident as both scratchboard plates crashed down to the ground while spraying because the tapes riped off on the backside. So there was dust and laquer rests which were dropped down on the surface. First I thought I crashed them completely but then I tried to sand all off and indeed it worked... so most of the damage is repaired. I had the usual problem that I sanded too much at the edges - unbelievable how fast you come to the wooden ground at these places...! Would recommend to avoid sanding every brink. I repaired the sanding-through areas by restaining them a little with the right colour. Worked quite good. So tomorrow I will add the last coat of laquer... just mentioning a little: The last coat was already quite even and very brilliant - why is it nesseceary to sand again before polishing?... well, I'll do anyway because everyonbe says the result is better...
have a good time,
Tom Sailor
4 Attachment(s)
Re: Moongazer Déjà-vu Electric Mandola kit
Hi folks,
just posting some pics after the last coat of laquer yesterday:
Attachment 86679Attachment 86680Attachment 86681Attachment 86682
the surface looks quite even except some large waves from the tears I wasn't able to remoe properly. Well, it will be obviously that it's a selfmade instrument. But most of the parts I can be satisfied with the result.
by the way: I used this laquer spray:
http://www.spraymax.de/index.php?id=361
I used some fine spraying knobs I bought, was better than the original
and then two crossed blanks, after a quarter of an hour another two crossed blanks. So in fact it's six coats of laquer now, every two after each other.
I should point out that I had a class 3 breathing mask and security glasses andI REALLY needed... the procedure would have been vbery unhealthy else...
Now I have to let it dry for two weeks beforre final sanding and polishing. I even know now why to sand before polishing; I tested both possibilities on a testing object. There are still some fine unevennesses into the laquer that you can only see from a very short distance. Finesanding removes them and I was astonished how much I could see that at the end of the process.
Bye until two weeks,
Tom
1 Attachment(s)
Re: Moongazer Déjà-vu Electric Mandola kit
Just added a fourth coat of laquer to the Mandola's body only... after three days drying it became obvious that some areas of the solid body were less laquered. On some areas there was a nice napless film and on some other there was kind of a nopped orange skin:
Attachment 86912
The neck and the scratchboards look very good, it's just the body. I suppose the Alder wood soaked up more of the laquer than the maple pieces (was the same with the water for sanding). I didn't use a filler spray first because they are sold for Nitro-based laquer only, so maybe the first coat was just okay to fill the cavities of the wood's masure and therefore three coats were a bit scanty. So I decided to give the body another very thoroughly sanding-between with 1200 grit and to spend the money for another can of laquer spray - the fifth one! But I tried that hard to bring it to the best result - I just didn't want to slob right now and to have a whinge later...
Until two weeks,
Tom
9 Attachment(s)
Re: Moongazer Déjà-vu Electric Mandola kit
So, time to put it together...
I had a little time last week, so I post the effort's result.
After two and a half weeks I started with the final sanding of the scratchboard plates (1200 and 2000 grit):
Attachment 87796Attachment 87795
I used this wooden stick as sanding block and I came along quite well with that. I had many unevennesses so I had much work to get an even surface... in fact, I did not match it. I was really afraid to sand through the laquer to the wood as it happened at one of the sanding-betweens. The laquer I used seems to have its difficulties. It builded large tears and next to them areas of less laquer so I had to be very careful. And I didn't match to get every nook out. Would need one or two more laquer coats to do that and I didn't have more laquer - and time. Next time I do with Nitrocellulose-based laquer as many other hobby luthiers do with their guitars.
Well, after doing my work as fine as I could for the moment I polished it with coarse-grained and then fine polish paste. really fine look
Attachment 87801
So I did with the neck:
Attachment 87802Attachment 87803
Then the moment I could add the tailpieces:
Attachment 87804Attachment 87802Attachment 87803
Last I finesanded and polished the body
Attachment 87805Attachment 87806Attachment 87807
the body looks really fine too after polishing.
more to come...
10 Attachment(s)
Re: Moongazer Déjà-vu Electric Mandola kit
Now it was time to drill the holes for the scratchboards. I wanted to use some of the pre-drilled holes from the original scratchboard, So I tried to mark them as exact as possible:
Attachment 87812
I bought a special driller for the countersink screws (bought some larger ones than the original screws that were included in the kit):
Attachment 87814Attachment 87815
drilled the holes with the pillar drilling machine of my grandad-in-law
Attachment 87816
Then I put some screening laquer on the backside of the scratchboard and to the milled-out parts of the body to prevent buzzing:
Attachment 87817Attachment 87818
Had some problems to put the electrics together:
Attachment 87819
and then I had to fit another problem I chatted with Tom some weeks ago. The wooden scratchboards are 3mm higher than the original plastic one. Too high for the neck because it is overlapping the scratchboard with ca. 1cm length. So I had to put some wood between. First I tried a 2mm plywood, bit that failed bevcause it was 1mm too thin. So I had to cut a piece out of the scratchboard plywood to put between body and neck, and the same for the bridge.
Attachment 87820
Another problem was the cable connector because I milled the edge and I had to bend it a little at the upper side...
Attachment 87821
4 Attachment(s)
Re: Moongazer Déjà-vu Electric Mandola kit
Fastening the neck...
Attachment 87822
While fitting the scratchboard I recognized I made a little mistake when I drilled the holes. I didn't match the right position. So I had to fit the scratchboard ca. 1/2 cm down to the bottom of the body, and therefore the bridge is not exactly in the position I wantet it to be... little too high to the neck...
Attachment 87823
Anyway I decided to settle for the result I was able to achieve for now. So time to add the strings and some other accessories:
Attachment 87830Attachment 87831
And then after 5 months building time my Dola finally gave its first tone last thursday noon... :mandosmiley:
Was a great adventure. Well, when the light is shining on, one can see the finish is not still perfect. Maybe I'll spend some extra time for it in summer. But for now I love the instrument. Will add some better pics and a review at the Pictures section... and some sound examples as well.
So this was my building thread, thank you everyone for reading and I hope some of you got some ideas for creating your own Mandolin kit projects...
Good luck to everyone,
Tom Sailor
Re: Moongazer Déjà-vu Electric Mandola kit